How the gravel calculator works
The calculator finds the volume of your area in cubic feet from its length, width, and depth, then adds your compaction allowance. It converts to cubic yards by dividing by 27, and to tons by multiplying cubic yards by the material's weight per cubic yard.
The default weight of 1.4 tons per cubic yard is a common planning figure for crushed stone and gravel. It sits between Missouri DOT's published weights for loose and compacted granite or limestone. Pea gravel, river rock, and crusher run all weigh different amounts, so use your supplier's number when you have it.
The formula
Cubic feet = length × width × (depth in inches ÷ 12) × (1 + extra %)
Cubic yards = cubic feet ÷ 27 · Tons = cubic yards × tons per cubic yard
Worked example
A 20 by 10 foot parking pad with 4 inches of crushed stone and 10 percent extra:
| Volume (20 × 10 × 4 ÷ 12) | 66.67 cu ft |
|---|---|
| With 10% extra | 73.33 cu ft |
| Cubic yards (÷ 27) | 2.72 cu yd |
| Tons (× 1.4) | 3.8 tons |
Most suppliers round orders to a half or whole ton, so you'd order 4 tons. If the stone is priced at $50 a ton, enter that and the calculator shows about $190 for the exact amount.
Tips for ordering gravel
Match the stone to the job
Angular crushed stone with fines locks together and is the usual choice for driveways and bases. Rounded pea gravel and river rock look nice in paths and beds but shift underfoot. Ask the yard what they recommend for your use.
Prepare the ground first
Remove sod and soft soil, and lay landscape fabric if you want to slow weeds and keep stone from sinking into the soil. Edging along the sides keeps gravel from spreading into the lawn.
Compact in layers
For a base, spread and compact gravel in layers a few inches thick rather than all at once. Thick single layers don't compact evenly and can settle later.
Frequently asked questions
How many tons of gravel are in a cubic yard?
It depends on the stone and how tightly it's packed. A common estimate for crushed stone and gravel is about 1.4 tons per cubic yard. Missouri DOT's conversion table lists loose granite or limestone at about 2,410 to 2,590 pounds per cubic yard (1.2 to 1.3 tons) and compacted at 3,060 to 3,300 pounds (1.5 to 1.65 tons). Ask your supplier for the weight of the exact product.
How much area does a ton of gravel cover?
At 1.4 tons per cubic yard, one ton is about 0.71 cubic yards, or 19.3 cubic feet. That covers about 58 square feet at 4 inches deep, 77 square feet at 3 inches, or 116 square feet at 2 inches.
How deep should a gravel base be?
It depends on the use. For interlocking pavers, the Concrete Masonry and Hardscapes Association lists a minimum compacted base of 4 inches for patios and walkways and 6 inches for residential driveways in ideal conditions, with more for weak soil, poor drainage, or freezing. Decorative gravel paths and beds are often 2 to 3 inches.
Why add extra for compaction?
Gravel delivered loose packs down when you compact it or drive on it. If you need a certain finished depth, you need more loose material than the simple volume suggests. The calculator adds 10 percent by default; increase it for a base you'll compact hard.
Is gravel sold by the ton or the yard?
Both. Quarries and many landscape yards sell by the ton because they weigh trucks, while others sell by the cubic yard. The calculator shows both so you can compare quotes.
How many bags of gravel equal a ton?
Bagged gravel is often sold in 0.5 cubic foot bags; check the label. At about 1.4 tons per cubic yard, a ton is about 19.3 cubic feet, or about 39 half-cubic-foot bags. For anything over a few hundred square feet, bulk delivery is usually far easier.
Sources
- Missouri Department of Transportation: Highway maintenance tables and conversion factors
- Concrete Masonry and Hardscapes Association: Proper concrete paver base and depth
Results are estimates for planning purchases. Check product coverage, local building codes, and manufacturer instructions before you buy or build.